1. Home
  2. Ultrasound in anaesthesia
  3. Troubleshooting
WHEN THINGS GO WRONG

Troubleshooting

The block is not working, you cannot see the needle, the patient is on anticoagulants: what to do, and where to read more.

DRAFT · AWAITING CLINICAL REVIEW

Quick answers to common problems in theatre, each with links to the pages that explain more. Use them alongside local guidelines and senior support.

Managing a failed blockWhy blocks fail, how to test a block, and a step-by-step plan when it is not working, including the failed catheter.

The block is not working

The patient still has feeling in part or all of the area, or the operation is about to start and the block is patchy.

What to do

  1. Give it time. Most blocks take 15 to 30 minutes; large nerves such as the sciatic can take longer.
  2. Test it properly: cold, pinprick and movement, nerve by nerve. The body map shows which nerve supplies the area that is missed.
  3. If one nerve is missed, a rescue block of that nerve further along its course may work. Check the total local anaesthetic dose first, including all doses already administered.
  4. Ask the surgeon to add local infiltration, or plan sedation, general anaesthesia or systemic analgesia.
  5. Never repeat a full dose beyond the maximum. Watch for signs of local anaesthetic toxicity.
  6. Tell the patient, and document what was missed and the actions taken.

Next time

  • Confirm spread around the nerve or in the correct plane before completing the injection.
  • Choose a volume that matches the block, and confirm the target in two views if uncertain.

Read more

I cannot see the needle

The needle shaft or tip has disappeared from the screen.

What to do

  1. Stop advancing. Never move an unseen tip forward.
  2. Move the probe, not the needle: slide or tilt the probe gently until the shaft comes back into the beam.
  3. Keep the needle exactly under the long middle line of the probe (in-plane).
  4. Use a flatter needle angle, or enter further from the probe. Steep needles reflect less echo back.
  5. Inject 0.5 to 1 mL of fluid (hydrolocation) and watch where it spreads: this shows the tip.
  6. Check depth, gain and focus. An echogenic needle helps for deep blocks.
  7. Out of plane: use the 'walk-down' method, seeing the tip as a bright dot at each step.

Next time

  • Align the screen, probe and needle hand before starting.
  • Rest the hand that holds the probe on the patient so it cannot drift.

Read more

The patient is on anticoagulants

The patient takes an anticoagulant or antiplatelet drug, or has had one recently.

What to do

  1. Find out the exact drug, dose and time of the last dose, and the kidney function.
  2. Check the timing table. Neuraxial and deep blocks follow the strictest rules; superficial blocks at compressible sites carry less risk.
  3. If the timing is not safe, choose an alternative: a more superficial block, a fascial plane block or a different plan.
  4. Plan catheter removal and the next anticoagulant dose with the same table.
  5. After the block, look for signs of bleeding or a haematoma, and of new weakness after a neuraxial block.

Next time

  • Ask about blood thinners at the pre-operative visit.
  • Use a block at a compressible site when the risk of bleeding is high.

Read more

I cannot see the nerve or the picture is poor

The ultrasound picture is dark or blurred, or the nerve cannot be distinguished.

What to do

  1. Check the probe orientation marker, then set depth so the target is in the middle of the screen.
  2. Adjust gain and focus. Use plenty of gel and good contact.
  3. Tilt the probe a little: nerves are brightest when the beam meets them at 90 degrees.
  4. Find a landmark first, usually an artery, and trace the nerve up and down from it.
  5. Use colour Doppler to tell vessels from nerves.
  6. Press gently to collapse veins, and release pressure before injection.

Next time

  • Scan before skin preparation, and choose the best view.
  • Use a curved low-frequency probe for deep targets.

Read more

Pain, tingling or high pressure on injection

The patient reports sharp pain or paraesthesia on injection, or the syringe is hard to push.

What to do

  1. Stop injecting at once.
  2. Pull the needle back 1 to 2 mm and look again. The tip may be in the nerve.
  3. Do not inject against high pressure. Watch that fluid spreads around the nerve, not inside it.
  4. If no spread is seen, the tip may be in a vessel: stop, aspirate and watch for signs of toxicity.
  5. After the block, record what happened and follow up any new numbness or weakness that lasts.

Next time

  • Inject slowly in small steps, aspirating between them.
  • Keep the needle tip in view at all times.

Read more

Original text © Nerve Blocks, written for trained clinicians. Follow your local guidelines, and call for senior help early.